- Bennvenn Dmg Screen Replacement Windows
- Cell Phone Screen Replacement
- Bennvenn Dmg Screen Replacement Repair
So I had some left over DMG parts and wanted to mod them. Anyways, see below for a few pics.
- Home › DMG 3' Backlit LCD Kit. DMG 3' Backlit LCD Kit. $45 00 $45.00. Unit price / per. While not a drop in replacement, this new screen does offer a superior backlight, amazing contrast and comparable refresh rate with the original. This can be seen in the image with the BennVenn SD logo - and is the absolute worst case example.
- Sep 16, 2018 New replacement DMG screens? (Page 1) - Nintendo Handhelds - Forums - ChipMusic.org - chipmusic.org is an online community in respect and relation to chip music, art and its parallels.
BennVenn 3' LCD Glass Lens PIL. This scratch resistant glass is to suit BennVenns 3' LCD board for the DMG system. It has a larger viewing window to compensate for the larger screen image. Comes with 3M adhesive applied to the rear to apply straight to the consoles. Produced in house on our industrial UV printer. Optifine mac download.
1st one I didNew yellow shell with black glass and blue buttons with LEDs
White backlight and bivert
2nd one
White shell and teal buttons (no LEDs this time), grey glass
Teal backlight and bivert
3rd one
Black shell, blue glass, blue buttons, white backlight
4th one
Black shell with white buttons and screen cover. Teal backlight.
5th one
This was a custom painted gold shell that I got a hold of for cheap, a black glass screen cover and black buttons. I did not have a bivert chip handy so this one just got a backlight. It turned out okay, but the bivert would have made it much better:
6th one
This is one of my favorites, a OEM clear PIL. I used a green backlight and bivert, and had some silicone buttons as well. Turned out amazing I think.
7th one
Again, another great one. This was using an OEM PIL green shell. I used the original grey buttons and added a new grey glass lens. Installed a yellow backlight and bivert.
I have also since done a few pockets too. A little bit more of a pain to work with and the AAA's don't seem to like to power a backlight that much either. But they still look nice.
1st pocket
Used an aftermarket clear blue shell with white buttons, and a yellow backlight. No bivert on this one.
Bennvenn Dmg Screen Replacement Windows
2nd pocket
Used an aftermarket DMG themed shell on this guy. and a white backlight with a bivert this time. i'll likely mod this one with a lipo battery since I still have it on hand, and it will help with powering the backlight.
Cell Phone Screen Replacement
If you want to do a divert mod, I would recommend doing that before the back light as it's much easier to check if it has worked on a stock screen (4th image)
Why/what is a bivert? basically its a chip that switches the pixels. Anything that was off is now on and vice versa. Apparently this gives a better contrast but I can't say I've confirmed this yet. Download mac os x 10.6.
Bennvenn Dmg Screen Replacement Repair
On your untouched back half of the gameboy, where the ribbon cable connector is, unsolder the 6th and 7th pin and bend them up. (if you can't count, its the two pins that go to the area where the bivert chip goes so just follow the connections, you'll be fine)
next solder the 3 holes in the bivert chip to the existing solder on the gameboys board. You may need to trim the excess of some other solder in that area.
Solder the 2 pins to the board
in the bottom corner of the bivert chip is the ground, this gets solders to the gameboys ground which is the 2nd solder point from the top right corner, shown in photo 3.
Then plug everything back in and see if your screen should be inverted. To then make the screen look normal, when you do the back light mod, turn the polarising film to the inverted position.